How to clean dolphin pool cleaner filters

how to clean dolphin pool cleaner filters

How to clean dolphin pool cleaner filters

Often, it is very difficult to find answer for How to clean dolphin pool cleaner filters. Because pools are mood lifters and a lot of fun, especially in summers. However, cleaning them and taking care of their related equipment can be an exhausting job if you don’t know how to do it properly.

Often, the dolphin pool cleaner filters get dirty and don’t work efficiently. Either they skip the debris on the floor or don’t cover the whole pool. It may indicate that you need to clean the filters. And if you don’t know that, don’t worry. We are here to tell you How to clean dolphin pool cleaner filters using different methods.

Methods to clean dolphin pool cleaner filters

Usually, just backwashing the filters by garden hose is recommended for Dolphin pool cleaner maintenance. But it isn’t enough sometimes. The filters get too dirty to get cleaned just by a backwash of a garden hose. 

So, you must analyze the filter condition and use an appropriate method to clean it. Different methods to clean depending upon the filter conditions are:

  1. Backwashing the filter with water
  2. Using a cleaning solution to clean the filters
  3. Using acid to remove minerals embedded in the filters

Whichever method, you first must take the filters out of the dolphin pool cleaner.

Taking the Filters out of the Dolphin Pool Cleaner

Getting filters out of the Dolphin pool cleaner is very easy. Just follow these steps.

Taking the Filters out of the Dolphin Pool Cleaner

  1. Turn off the Dolphin pool cleaner if it is working and get it out of the water.
  2. Open the upper hatch on the dolphin pool cleaner. It may be a single hatch or double depending upon the type of your dolphin pool cleaner.
  3. Grab the handle of the filter bucket and slightly wiggle it and pull it out of the hatch.
  4. Detach the filter panels one by one from the filter bucket. Use the numbering on the filter panel if available and take them out in order.
  5. First, pull out the lengthy front filter panels and then the relatively shorter side filter panels.

Now, inspect the filters and check the level of dirt on their surface. Then apply one of the above-mentioned methods to clean them.

1- Backwashing the Filter with Water

This is the easiest and widely used method if you clean your dolphin pool cleaner filters once after two weeks or so. The dirt gets out of the filters easily and you get clean filters ready for use again.

How to clean dolphin pool cleaner filters with water:

To clean dolphin pool cleaner filters by using water, follow these steps.

Step 1: Take the filter panels out

Take out the dolphin pool cleaner filter panels and place them at some suitable place where you want to clean them.

Step 2: Wash the filter panels with the water hose

Wash each panel with the water hose and take the dirt out of the filter panels.

Step 3: Wash the filter bucket

Wash the bucket too. It has dirt residing in the corners. Don’t forget to wash the underside of the bucket.

Step 4: Check the filter

Once cleaned, check the filters panels, and see if there is any dirt left. If it is clean, then assemble the filter and fit it back in the dolphin pool cleaner. Otherwise, use a cleaning solution or acid, as you find suitable.

Note: Remember to clean the filters at some solid place. If you clean it on grass, the salts and minerals of the filter dirt can kill the grass. So, choose a place accordingly.

2- Using a Cleaning Solution to Clean the Filters

Cleaning solutions are used if there is sunblock or bathing lotion mixed in your pool water. It makes the water greasy, and a thin film is attached to the filters which hold them from working properly. 

If you find such films or oils on your dolphin pool cleaner filters or the dirt is too sticky to leave by just backwashing the filter, then you should use the cleaning solution.

You can find the cleaning solution at a suitable price. One pound of cleaning solution is usually enough for five gallons of water.

How to clean dolphin pool cleaner filters by cleaning solution:

How to clean dolphin pool cleaner filters by cleaning solution:

To clean dolphin pool cleaner filters with cleaning solution, follow these steps.

Step 1: Take out the filter panels

First, take out the filter panels from your dolphin pool cleaner and put them where you have the bucket for cleaning them. Secondly, wash them with a garden hose to clear the thick debris.

Step 2: Make a solution of water and cleaning solution

To do this, take a bucket according to the size of your filter panels i.e., the filter panels should easily submerge in that bucket. 

Then fill it just below the top and add the cleaning solution according to the water in the bucket.

Step 3: Submerge the filter panels in the solution

Pick up the filter panels and place them in the solution bucket one by one. Make sure that each panel is completely submerged in water.

Step 4: Take the panels out after a day and assemble them

One day is enough to keep your dolphin pool cleaner filter panels in the cleaning solution. After that, take them out and wash them with water.

Your dolphin pool cleaner filter panels should be clean by now. Assemble them in the opposite manner of how you disassembled them and you’re good to go.

3- Using Acid to Remove Minerals Embedded in the Filters

Sometimes, the minerals from the chemicals added to the pool water get embedded in the dolphin pool cleaner filters and make it difficult for them to work properly. In this case, using acid to remove the minerals is the only option left.

However, use this method very rarely as it can damage the filters permanently. Using it once a year at the end of the season is more than enough.

Also, remember to use protective equipment when you use acid since it can damage your skin and eyes. In addition, wear a mask so you don’t breathe the acid into your lungs.

You can use muriatic acid mixed with water for cleaning the filters.

 How to clean dolphin pool cleaner filters using acid:

How to clean dolphin pool cleaner filters using acid

Follow these steps to clean the dolphin pool cleaner filters using muriatic acid.

Step 1: Take out the filter panels

Take the filter panels out of your dolphin pool cleaner and give them a little wash with a garden hose to clean the thick debris.

Step 2: Make a solution of Muriatic acid with Water

Take a bucket of the size of your filter panel and make a solution with one to four ratios of acid to water. 

Step 3: Put the filter panels in the solution for one day

After making the acid solution, place the filter panels in the solution for about a day. This will clean all the minerals stuck in the filter panels.

Step 4: Take out the filter panels and wash them

After one day, take out the filter panels and wash them with water. They should look clean and white as new after the acid wash.

You can use a pH neutralizer to neutralize the acid and pour it into the drain line. 

Step 5: Assemble the filter panels back to the bucket

After washing the filter panels, assemble them in the reverse order as you disassembled them and fit them into the dolphin pool cleaner.

Now, you have a ready-to-work dolphin pool cleaner with clean filters.

Conclusion

To enjoy a clean pool, you must keep the cleaner clean. Here, a detailed answer is provided for How to clean dolphin pool cleaner filters.

Keep in mind that these methods can be applied on dolphin premier robotic pool cleaner filters and dolphin nautilus pool cleaner filters too.

You can estimate the level of cleaning required by dolphin pool cleaning filters by taking them out. If there is only a small level of dirt, just a wash with your garden hose is enough.

Otherwise, you can use a cleaning solution or acid to clean dolphin pool cleaner filters depending upon the level of clearance required.

Leave a Comment