How to Install Above-Ground Pool [Detailed Guide]

How to Install Above-Ground Pool

There are many above-ground pools on the market today that provide hours of family fun and great workouts when the weather is too hot for other activities. How to install an aboveground swimming pool depends on the type and quality you choose. Installation can be quick, easy, and cost-effective if you prepare in advance.

Easy To Understand Guidelines About Above-ground Installation:

There are no manufacturer’s instructions in this guide since this is just a general guide to aboveground pool installation.

Choose a suitable location for your Pool

You should take the time to find out where the pool is located. It is advisable to choose a place where the sun stays the longest during the day. Pool equipment is recommended to be kept within 4 feet of the pool wall as it puts less pressure on the pump. Ground pool pumps operate on gravity, so keep your pool equipment close to the pool. Also, make sure your pool is visible from your home.

Mark the border and prepare the Ground

Once you have chosen the right area for your pool, you will need to dig an iron rod in the center of the site and use a tape measure to draw a circle around it. Whatever the size of the pool, add an extra leg around the pool. This helps prevent the growth of grass and weeds around the pool walls. On this other stand, you can also place decorative stones and plants to decorate the pool area.

Using a sod cutter, cut the grass inside your circle. If you cut the grass into long strips, remember to roll it up and use it later in the pool. Then clear the area to remove any remaining grass, roots, stones, or debris. This is important. Otherwise, it will adversely affect the lining.

The Lower Level

The higher lands in the cleared area must be excavated to match the lowest grounds. During the aboveground pool setup process, always make sure everything is balanced correctly. A more accessible and more accurate way to do this is to use the site level or navigation level for this purpose. Uneven floors can damage the pool and cause harm to the pool and its surroundings. The walls can collapse or fall to the ground. Once the ground is level, measurements should be taken before construction begins.

Ground Level

The higher lands in the cleared area must be excavated to match the lowest grounds. During the aboveground pool setup process, always make sure everything is balanced correctly. A more accessible and more accurate way to do this is to use the site level or navigation level for this purpose. Uneven floors can damage the pool and cause harm to the pool and its surroundings. The walls can collapse or fall to the ground. Before beginning construction, the ground should be leveled.

Additional Advice

When the ground is clay, use floor pads for installation. A free oval buttress basin requires more space due to the need for leg support. With concrete, you won’t be able to install an oval pool. Floor cushions should be flat and should not be installed in bowl-shaped pools. Oval basins must not be placed on a plate with straps. The pool must be level around the perimeter.

Basics of Swimming Pools

Once the ground is leveled, it’s time to lay the foundation for the underground pool. Use clean sand as your base material as it serves a dual purpose. In the first place, it acts as a barrier between the soil and the lining and protects it from objects like rocks or roots. Second, it provides cushioning at the bottom of the pool, making your feet more comfortable. For extra protection of the pool lining, it is recommended to use sanded floor mats in the treble and spa storage. Replacing a liner costs money in liner filling, installation and pool, so it is worth investing in liner protection.

Standard sand is 2 inches, but consult the manufacturer’s instructions. Also, do not use alkaline solid substances such as peat moss as a base to corrode metal parts.

Pool frame foundations

The base of the pool frame is a patio stone or block embedded in the ground. Place them under the pool columns and buttresses to support these blocks. It is essential to be convinced in two ways. First, each block should be placed in all directions (left and right and front and back), and the second block should be coplanar with each other. This ensures that the baseplate, track, and pool frame are firmly and evenly distributed over the block. Check the pool builder’s instructions for placing the stones and blocks.

Once you have decided on the actual location of the floor where you will place the unit, make sure all the struts are level. From one block to the next, the level cannot exceed 1/16 inch. Use the pass to make sure each block is cleared. Even if the difference between the blocks is only 1/8 inch, unstable support can cause the aboveground walls of the pool to warp. Follow the manufacturer’s instructions regarding the timing and number of blocks to be placed.

You need to constantly check and re-check this critical frame positioning as you lay the block when you install the wall when you spread the sand base when you bevel the cove area before you install the liner.

According to the manufacturer’s instructions, a 2-inch layer of sand is standard. Also, do not use highly alkaline substances such as peat moss as a base, as they can corrode metal parts.

Combination of pool

Ground pools typically include lower rails, lower slabs, pillars, pool walls, upper railings, pillar covers, skirting boards, pool liners, and equipment. It usually consists of a scraper and a backlink. If the pool is delivered by truck, ensure that all critical parts are in good condition and are not missing or damaged.

After installing the pool frame and walls, create the bay. This is a 6 “to 8” sand wedge built along the inner edge of the pool wall. The compartment prevents the liner from slipping under the pool wall and provides a protective layer between the liner and the pool’s metal frame. 

There are alternative pool compartments pre-produced in two forms: peel and stick. Peel and sticks have a sticky lining and click and stick that snap to the railing on the pool wall.

Install the Liner

Building an above-ground pool starts with the next step, called lining. Liners are fragile and require additional care to reinstall and inspect, check for holes and crevices, and check seams to ensure proper sealing. Of course, you don’t want to find any flaws after filling the pool. Follow the manufacturer’s instructions for installing the liner. Ensure there are no gaps between the primer and the floor and that there is no pressure on the primer. Depending on the type of liner (overlap, collar, or J-hook), hang the liner over the pool. 

Liner wrinkles are normal and cannot be avoided. To keep the liner secure, do not pull or stretch the liner. A liner and pool wall can wrinkle because of air trapped between them. A vacuum hose can be inserted into the skimmer opening in the pool wall behind the liner to minimize this. 

Adjust the pool liner while sweeping. After the pool liner is installed, you can continue to fill the pool and create a vacuum. You can fill your pool with a regular garden hose or rent a much faster water tanker.

Connect Pool Equipment

After the aboveground pool is filled with water, pumps and filtration systems, heaters, lights, and other pool equipment need to be connected. Follow the manufacturer’s instructions for pool equipment and the exact instructions for adding chemicals to the aboveground pool.

Enjoy!

Congrats! After installing your aboveground pool, you have completed it. It is not an easy task, but we respect you for accomplishing it.

The area around your pool must be kept free of obstacles: kids love to run, and a trip hazard can change a great afternoon into an emergency room visit.

Leave a Comment